Everbuild Lumberjack 5 Minute PU Wood Adhesive Gel – 310ml 
Everbuild Opti-Mix Mortar Plasticiser - 1 Litre (Box of 12) 
ALM Code 8 Milled Lead - 210mm x 3m 
Soudal Genius Gun Pipe & Plumbing Foam – 600ml 
Soudal Trade Sanitary Silicone - White 290ml 
Bora Workhorse Single Piece Stand with Folding Legs PM-3350 
Siroflex Trade Clearbond Adhesive Internal Use - Clear 290ml 
Timloc Double Pantile Tile Vent Brown (Box of 6) 
Everbuild Bath & Kitchen Sealant - 200ml 
ALM Code 7 Milled Lead - 914mm x 6m 
Everbuild Forever White Silicone Sealant – 295ml (Box of 12) 
ALM Code 3 Milled Lead - 850mm x 6m 
Everbuild Everflex 200 Contractors LMA Silicone - White 295ml 
Soudal PVCu Solvent Frame Cleaner - 1L (Box of 12) 
Bostik Builder Tape, 50mm - 25m Shed Felt
Best Sellers
-
Everbuild Patio Wizard – 1 Litre
£6.49 Incl VAT £5.41 Excl VAT Add to basket -
Code 4 Cast Lead – 1200mm x 6m
£419.83 Incl VAT £349.86 Excl VAT Add to basket -
Corrapol-BT Rock n’ Lock Wall Flashing
From: £52.26 Incl VAT £43.55 Excl VAT Select options This product has multiple variants. The options may be chosen on the product page -
Gorilla Wood Glue – Brown 236ml
£8.99 Incl VAT £7.49 Excl VAT Add to basket -
Samac Galvanised Round Wire Nails – 65mm x 3.35mm
From: £7.49 Incl VAT £6.24 Excl VAT Select options This product has multiple variants. The options may be chosen on the product page -
Aluflow Rock N Lock Gutter Bracket – (RAL Colours)
£13.70 Incl VAT £11.42 Excl VAT Read more
Frequently Asked Questions (3)
Yes, shed felt should be used on a shed as it helps prevent water entering your shed and will keep your belongings in the shed dry.
There are many brands offering shed felt. At ERoofing, we recommend using IKO shed felt or Icopal shed felt.
You could opt for felt shingles if you're not looking to use a typical shed. They offer a more stylistic look and can easily be laid without much roofing experience.
Shed Felt
We stock a great range of shed felt and roof felt perfect for your home DIY project. If you need any advice on how to felt a shed roof or the amount of felt you may need, then give us a shout or read one of our guides. Browse through our range of cost-effective, easily applied shed felt.
Replacing Shed Felt
If you need to replace your shed felt due to leaking or a simple cosmetic tear, ERoofing will have the perfect choice for you. From Chesterfelt to Icopal, we stock various suppliers that hold high-quality shed felt fit your shed or garden bar. The shed felt we stock can be felted with nails or appropriate adhesive. If you’re unsure of what you need, make sure to get in touch with us to talk about replacing or repairing your shed roof.
Alternatives to Shed Felt
If you’re not looking to use shed felt or have some reservations, you can always try out EPDM membranes. They are gradually a safe potential alternative for small garden buildings.
Installing & Laying Shed Felt
To get started, make sure to delicately terminate any existing timber fascia boards applied to the front, back and flanks of your shed. Being careful is critical as you don’t want to cause any damage. Next, use a solid hammer to remove the nails holding down the old felt roof, then strip the old felt. Make sure the surface is free and dry. If you notice any nails sticking out or missing, please replace them promptly.
You will need enough felt to cover the entire roof area with a bit of extra on each edge, around 2 inches, as this allows for overlaps.
You will need to cut three pieces of felt. Two pieces for each side of the pitched roof, and a third piece that will overlay the two side sections on each side and run along the top ridge of the shed. Apply the cut felt to either side of the roof, stretching it tight so that it lies flat before nailing it at around 10cm intervals along the length of the roof, just below the apex. Following, you can hammer in the nails along the bottom edge of the roof at wider intervals, around one every 30cm.
Once you’ve secured the side panels in place, add the top section to the ridge and fix it using high performance felt adhesive applied with a paintbrush, then hammer it at the lower edge at 5cm intervals.
Tidy up the overlap at each edge by folding it down and nailing it securely. Next, use your craft knife to cut a slit in the felt overhang at the apex of the roof, then fold the felt down there and nail securely at 10cm intervals along the roof. Use wood nails to fasten them in place and your craft knife to trim away any excess material.
