Name: Everbuild No Waste Foam – 750ml
SKU: NOWASTEHH
Availability: OutOfStock

Uses

The No Waste Expanding Foam by Everbuild is the ultimate, unrivalled expanding foam on the market that's applied directly from the can. This is because most conventional expanding foams clog after one application due to the foam curing inside the nozzle. However, the technicians at Everbuild thought long and hard to achieve a new nozzle design that prevent this, ensuring that you can apply this product in January, then again in September without concerns of it jamming. Applications this product is typically used in include;

Irregular gap filling in stone, brick, plaster or concrete
Filling gaps around pipe entries through walls and gaps around window and door frames
Electrical wire chasing before plastering
Deep joints before applying a sealant for pointing or plaster
Insulate behind cladding to exterior walls and behind soffit and barge boards.
Fixing window and door frames, timber structures and window sills and thresholds

Preparation

Before starting the application, check the surface and clean it if needed, removing contaminants on the surface that can hinder the adhesion, such as dirt, grease, dust, oil, etc.

Application

Shake the can thoroughly (about 20 times) before using
Carefully fix the nozzle to the can, ensuring you don't overtighten or force
Always apply this product whilst holding it upside down
Partially fill the cavity, working from the bottom upwards, and the expanding foam will fill the rest
If you're fixing door or window frames, support must be used until it's cured and must be used in conjunction with mechanical fixings

Limitations and Notes

Despite this product having a bespoke nozzle to combat the curing expanding foam, you must still clean it after using a Gun Foam Cleaner; otherwise, you risk clogging.
Ensure you don't leave it in direct sunlight when transporting and storing.

Additional information

Chemical Base	Polyurethane
Density	ca. 17 kg/m3 (bulk density of foam)
Compressive Strength	2 N/cm2 (DIN 53421) at 10% stress
Tensile Strength	10 N/cm2 (DIN 53430)
Elongation at Break	26%
Shear Strength	6 N/cm2 (DIN 53427)
Yield	100%-150% of its original volume following discharge 35 litres (750ml can)
Substrate Temperature	5°C – 25°C. (Optimum 20°C)
Cutting Time	18 – 21 mintes on a 20mm bead
Tack Free Time	11 – 13 minutes
Cell Structure	Medium fine
Temp Res Of Cured Bead	Long Term: -40°C to +80°C Short Term: -40°C to +100°C

Technical Data Sheet

Safety Data Sheet

Chemical Base

Polyurethane

Density

ca. 17 kg/m3 (bulk density of foam)

Compressive Strength

2 N/cm2 (DIN 53421) at 10% stress

Tensile Strength

10 N/cm2 (DIN 53430)

Elongation at Break

26%

Shear Strength

6 N/cm2 (DIN 53427)

Yield

100%-150% of its original volume following discharge
35 litres (750ml can)

Substrate Temperature

5°C – 25°C. (Optimum 20°C)

Cutting Time

18 – 21 mintes on a 20mm bead

Tack Free Time

11 – 13 minutes

Cell Structure

Medium fine

Temp Res Of Cured Bead

Long Term: -40°C to +80°C
Short Term: -40°C to +100°C

FREE Next Working Day Delivery on Orders over £10*

Everbuild No Waste Foam – 750ml

Additional information

Technical Data Sheet

Safety Data Sheet

Product Information

Technical Data Sheet

Safety Data Sheet

Related Products

Everbuild Everflex 200 Contractors LMA Silicone - Brown 295ml (Box of 25)

Everbuild 402 Waterseal – 5 Litre

Soudal Cleaner & Degreaser - 400ml

Recommended products

Everbuild Stixall Extreme Power – White 290ml (Box of 12)

Cromapol Acrylic Roof Coating – 5kg

IKO Super Shed Felt – Black 8m Roll

Get new offers to your inbox.