ALM Code 8 Milled Lead - 760mm x 3m 
Soudal Trade Gun and Foam Cleaner - 500ml 
Everbuild Black Jack 904 Roof Felt Adhesive – 2.5 Litre 
ALM Code 6 Milled Lead Flashing - 450mm x 6m 
Everbuild Showerproof Bathroom Silicone - Clear 280ml (Box of 12) 
Ronseal Ultimate Finish Interior Floor Pad Kit 
Bond It All Weather Roofing Compound - Black 2.5L 
Code 6 Cast Lead - 180mm x 6m 
Code 8 Cast Lead - 600mm x 3m 
OX Tuff Carbon Marking Pencil Value Pack 
Everbuild Jetcem Plaster Rapid Repair – 6kg 
OX Trade Plastic Speed Rafters Square Set 
Ronseal One Coat Stays White Radiator Paint - Matt 750ml 
ALM Code 3 Milled Lead - 1200mm x 3m 
Ronseal Stays White Ultra Tough White Matt Paint - 750ML 
Code 7 Cast Lead - 850mm x 3m 
Bond It 5 Minute PU Wood Gel Translucent 300ml - Box of 12 
Timloc Castellated Tile Vent Terracotta (Box of 8) 
SikaFlex 221 Adhesive & Sealant - Black 300ml (Box of 12) 
Hambleside Danelaw Double Pantile Vent TV15/2 - Terracotta (Box of 5) 
Cast Lead Dome Set (Lead Dots) - Pack of 20 
Timloc Interlocking Plain Tile Vent Grey (Box of 12) 
Bond It B3 Fill And Fix Expanding Foam Aerosol - Beige 750ml 
Everbuild Pinkgrip Dryfix FR – 750ml 
Over Fascia Vent, 10mm 
Bond It Aerosol Spray Adhesive - 500ml Beige 
Gorilla Glue - Dark Brown 1L 
FloPlast Half Round Union Unit - White 
OX Trade Metric Tape Measure - 8m 
Everbuild PVCu Acti-Spray – Clear 200ml 
Uses
The Everbuild Lumberjack Wood Preserver is suitable for various applications; however, you should only use the Clear colour when looking for an internal application. You can use this internally as a final finish for a natural wood effect; however, it is not water-resistant. So when looking at an external application, the Clear variation of this product is fantastic at providing properties and protection for the wood. Still, you should protect it with either overpainting, varnishing or staining.
The Fir Green, Dark Oak, Golden Chestnut, Red Cedar and Slate Grey should be used externally, and they are ideal for rough-sawn or planed timber. These include areas such as;
- Window Frames
- Fences
- Sheds
- Cladding
- Horticultural timber
- Roof timber
- Joist and many more
You need to treat the colour variations of this product the same as the clear colour. After applying this product to the surface and it's dried, you should coat it with a varnish, overpainting or staining.
Preparation
Before applying this product, ensure you prepare all the surfaces. Remove any pain, varnish, stain, grease, bark, or other contaminants that may hinder this product. If decay is present, remove all of it and replace it with sound timber. You can apply this to damp surfaces.
Application
Shake well before use; this product is ready and doesn't need to be diluted.
- Apply by brush, spray or dipping
- Applying a coat along the wood covering the whole surface
- Wait for it to dry completely
- Apply a second coat onto the surface
- To ensure the end grains are fully coated, soak them in the preserver for about 3 minutes.
Limitations
- Always use coarse rather than fine mist generators
- Do not apply to the surface on which food is prepared
- Avoid contact with bitumen, roofing felt or plastics
