Armatool Flooring Kneepads 
Everbuild 5 Minute Polyurethane Wood Adhesive Gel - 310ml (Box of 12) 
Freeflow 65mm Square Gutter Drain Pipe 112° Branch - White 
OX TOOLTREK Modular Storage System - 3 Piece 
Bostik Flashband Self Adhesive Flashing Tape – Grey 3.75m x 75mm 
Timloc Plain Tile Vent Red (Box of 14) 
FloPlast Half Round Gutter 90° Bend, Brown – 112mm 
Soudal Lead Sheet Sealant 290ml - Grey (Box of 12) 
Everbuild Bath & Kitchen Sealant - 200ml 
ALM Code 8 Milled Lead - 300mm x 6m 
Samac Half Round Snowguard Bracket - 225mm (9") 
Bond It Rain-Mate All Weather Sealant - Clear EU3 
Everbuild Everflex 200 Contractors LMA Silicone - Transparent 295ml (Box of 25) 
OX Pro Mortar Spike, 300mm 
Soudal Vaseline Lubricating & Protective Spray – 400ml 
FloPlast Downpipe Rainwater Diverter Kit RVS1 
ALM Code 5 Milled Lead - 150mm x 3m 
Code 8 Cast Lead - 760mm x 6m 
Everbuild Resiblock Trade – Clear 5 Litre 
Everbuild PVCu Acti-Spray – Clear 200ml 
Ronseal One Coat Water-Based Tile Paint - Granite Grey Satin 750ml 
ALM Code 4 Milled Lead - 300mm x 6m 
Bond It Cove-Mate Coving Adhesive - White EU3 
Bond It Superglue Activator Accelerator Spray Cyanoacrylate Aerosol - 400ml 
Estwing Hammer Curved Claw Smooth Face - 20oz 
Soudal Orange Skeleton Gun - Up to 400ml 
Timco 8 Spanner Set 
Code 6 Cast Lead - 450mm x 3m 
Everbuild General Purpose Silicone - Grey 280ml (Box of 12) 
Soudal Trade Sanitary Silicone - White 290ml 
Everbuild Salt-Away Salt Remover – 5 Litre 
Everbuild Everflex 115 G.P Building Mastic - Brown 285ml (Box of 25) 
Bond It Mega Stik PU Adhesive - Beige 750ml is a fast-curing adhesive foam. Designed specifically to aid in the installation of plasterboard, insulation boards, floorboards and roof decking.
It adheres well to most commonly used building materials: plaster, wood, metals, bituminous membranes and mineral wool and can even be used in place of backing rods in expansion joints and around window and door frames.
Preparation
Ensure to cover all surrounding surfaces with paper or plastic sheets to protect them from any drips of foam.
- The foam needs moisture to begin the curing process, mist the substrate with water prior to application
Application
When applying this product, make sure to wear gloves and eye protection at all times.
- If needed, warm the cans in some lukewarm water (not above 50°C) and shake for at least 30 seconds before fixing to the foam gun.
- Apply the beads to the substrate and leave for approx . 2 minutes before pressing into place. Hold board in place for around 1 minute until adhesive has began to cure.
- You should apply the boards in rows, starting from the bottom of the wall and working up to the top to avoid sliding.
Plastering can be done after 1 hour of application.
Limitations
- Cured foam is sensitive to direct sunlight and UV light so should be covered with an opaque sealant, filler, paint or other suitable material.
- Not recommended for use on polyethylene, silicone, oil and grease
