Code 4 Cast Lead - 914mm x 3m 
Soudal Soudalead PB Lead Sealant - Grey 300ml 
Ronseal Diamond Hard Floor Paint - Anthracite Satin 750ml 
Soudal Grip ALL Solvent-Free - White 290ml 
Klober Uni Angle Ridge End Cap, Black 
Timloc Castellated Tile Vent Red (Box of 8) 
Soudal Mitre Kit 50g + 200ml - Clear (Box of 12) 
FloPlast Square Line Running Outlet Black – 114mm x 65mm 
FloPlast Half Round Gutter 90° Bend, Brown – 112mm 
Bond It Gripbond - Solvent-Free Adhesive - White 350ml 
Everbuild Caulk Once – White 380ml 
Everbuild Stixall Extreme Power – Brown 290ml 
Soudal Firecement HT, Black - 300ml 
ALM Code 4 Milled Lead - 180mm x 3m 
Easy-Trim Universal Dry Verge System - Grey 
ALM Code 3 Milled Lead - 1600mm x 6m 
Bond It Barrier Tape Yellow and Black - 70mm x 500M 
Ronseal Exterior Multi-Purpose Smooth Finish Filler - Grey 1.2Kg 
Timloc Castellated Tile Vent Brown (Box of 8) 
Bond It Dustproof & Hardener - Clear 5L 
ALM Code 5 Milled Lead - 150mm x 6m 
Timco Screwdriver 8-Tool Set 
Bond It Multi-Purpose Low Viscosity Spray Lubricant - 400ml Clear Roof Felt Adhesives
Best Sellers
-
FloPlast Half Round Running Outlet, Black
£5.99 Incl VAT £4.99 Excl VAT Add to basket -
ALM Code 7 Milled Lead – 760mm x 3m
£229.39 Incl VAT £191.16 Excl VAT Add to basket -
Easy-Trim Universal Dry Verge System Terracotta (Box of 50)
£67.50 Incl VAT £56.25 Excl VAT Add to basket -
Timco FirmaHold Collated Brad A2 Stainless Steel Nails – 16G x 50mm (2000 Pieces)
£34.99 Incl VAT £29.16 Excl VAT Add to basket -
Ulti-Mate Stonewold Mk2 Roof Tile Vent – Grey
£59.99 Incl VAT £49.99 Excl VAT Add to basket -
Code 8 Cast Lead – 300mm x 6m
£205.63 Incl VAT £171.36 Excl VAT Add to basket
Roof Felt Adhesives
Browse through our range of roof felt adhesives. At ERoofing, we stock a substantial range of high-quality felt adhesive that come in ranging sizes from 1 litre to 25 litre.
Applying Felt Adhesive
You must apply felt adhesive either using a stiff brush, mop or squeegee. To avoid thickening in cold weather, stock the felt adhesive in a warm room before — for more straightforward application.
Cromar Roofing Felt Adhesive, in particular, should be applied to the surface and left for 15 to 30 minutes (depending upon drying conditions) to develop its full thickness.
The felt should then be placed into the wet adhesive film carefully, rubbing or rolling each section down to ensure highest contact with the adhesive and to expel air trapped between the surface and the felt. Wherever possible, the felt should be unrolled into the roofing felt adhesive and rolled with a light roller (15 to 25kg).
The overlaps should be at least 75mm on the side and 150mm at the ends. To ensure a complete bond at the side and end laps, Cromar Roofing Felt Adhesive can be applied to the underside of the felt and well compacted.
When using with a timber structure, the first layer of felt must be nailed down. Successive layers of felt may then be bonded using Cromar Roofing Felt Adhesive.
When used on concrete surfaces that are porous, it will be necessary to prime the surface first, ensuring that the primer is completely dry before the first layer of felt is applied.
Twenty-four hours after laying felt, check all bondings to ensure that full adhesive has been obtained. Mainly check all laps.
