Samac Stainless Steel Cladding Pins - 30mm x 2.0mm (Box of 250) 
Code 3 Cast Lead - 1200mm x 6m 
Everbuild P18 Gas Leak Detector - 400ml 
Soudal 5 Minute D4 Wood Adhesive Liquid – 750g 
Samac Hall Hooks - (Bags of 10) 
Everbuild Opti-Mix Cement Colourant – Black 1 Litre 
Everbuild Resiblock Block Paving Sealer - Matt 5 Litre 
Timloc Non-Profile Tile Vent Red (Box of 8) 
Bostik Flexacryl Instant Repair Waterproofing - Grey 5kg 
Timco Carpenter’s Speed Auger & Flat Wood Bit Kit 
Klober Small Slate Vent - Slate Grey 
ALM Code 5 Milled Lead - 390mm x 6m 
Ronseal Exterior Yacht Varnish - Satin 500ml 
Easy-Trim Universal Dry Verge System Terracotta (Box of 50) 
Evo-Stik Impact Adhesive - 500ml 
ALM Code 7 Milled Lead - 510mm x 3m 
Hambleside Danelaw (HD PCSPA) Tile Vent Adaptor and Flexi for TV10 Range 
Everbuild Lumberjack 550 Floor Adhesive – 600ml (Box of 12) 
ALM Code 8 Milled Lead - 510mm x 6m 
Spax Pozi Pz2 Drill Bits - 25mm (Pack of 5) 
Bond It Bitumen Paint - Black 25L Roof Felt Adhesives
Best Sellers
-
Code 4 Cast Lead – 850mm x 6m
£297.02 Incl VAT £247.52 Excl VAT Add to basket -
Code 6 Cast Lead – 240mm x 6m
£122.81 Incl VAT £102.34 Excl VAT Add to basket -
Cromar Bitumen Trowel Mastic – Black 1L
£14.94 Incl VAT £12.45 Excl VAT Add to basket -
ALM Code 6 Milled Lead Flashing – 300mm x 6m
£152.93 Incl VAT £127.44 Excl VAT Add to basket -
FloPlast Half Round Union Unit – White
£1.89 Incl VAT £1.58 Excl VAT Add to basket -
Everbuild Overlap & Border Adhesive – White 250g
£4.99 Incl VAT £4.16 Excl VAT Add to basket
Roof Felt Adhesives
Browse through our range of roof felt adhesives. At ERoofing, we stock a substantial range of high-quality felt adhesive that come in ranging sizes from 1 litre to 25 litre.
Applying Felt Adhesive
You must apply felt adhesive either using a stiff brush, mop or squeegee. To avoid thickening in cold weather, stock the felt adhesive in a warm room before — for more straightforward application.
Cromar Roofing Felt Adhesive, in particular, should be applied to the surface and left for 15 to 30 minutes (depending upon drying conditions) to develop its full thickness.
The felt should then be placed into the wet adhesive film carefully, rubbing or rolling each section down to ensure highest contact with the adhesive and to expel air trapped between the surface and the felt. Wherever possible, the felt should be unrolled into the roofing felt adhesive and rolled with a light roller (15 to 25kg).
The overlaps should be at least 75mm on the side and 150mm at the ends. To ensure a complete bond at the side and end laps, Cromar Roofing Felt Adhesive can be applied to the underside of the felt and well compacted.
When using with a timber structure, the first layer of felt must be nailed down. Successive layers of felt may then be bonded using Cromar Roofing Felt Adhesive.
When used on concrete surfaces that are porous, it will be necessary to prime the surface first, ensuring that the primer is completely dry before the first layer of felt is applied.
Twenty-four hours after laying felt, check all bondings to ensure that full adhesive has been obtained. Mainly check all laps.
